Pyromation makes precise, highly-accurate sensors used in the medical industry. Many of these assemblies are sanitary Clean-In-Place (CIP) sensors that are available with transmitters and thermowell protection and are 3-A approved. Besides being precise in temperature measurement, some of the sensors are designed for fast response times – critical in laboratories and environmental chambers.

More rugged sensors are available for use in the high-temperature stress found in medical autoclaves and sterilization equipment.

 

AUTOCLAVES, ENVIRONMENTAL CHAMBERS, AND STERILIZERS

FERMENTATION, SANITARY/CIP

LABORATORIES AND CHILLERS

VALIDATION AND CALIBRATION

 

THE PREMIER MANUFACTURER OF RTD TEMPERATURE SENSORS,

THERMOCOUPLES & THERMOWELLS IN NORTH AMERICA

 

 

Check out the Pyromation Product pages on Anderson Controls!

Bellypack RANGER Systems

Product page: RANGER Remote Control Systems for Hydraulics 

Our belly pack RANGER systems are a simple, cost-effective way to retrofit a wireless remote on a manual hydraulic system with 4 to 6 axes of variable speed control.

The package is supplied with electrical actuators to stroke the valves in both directions, and all hardware to connect the actuators to the valve handles or linkages. The actuators are connected to the receiver with a premade harness.

The belly pack RANGER is fast and smooth; it responds in 0.05 seconds and feathers all of the crane functions. Installation is simple with our illustrated manual.

Four or six proportional paddles control the winch and boom, and additional toggle switches drive the auxiliary functions and boom speed selection. There is a key switch mounted on the side for turning the transmitter on and off, as well as starting the engine. Side-mounted, sealed pushbuttons are used for increasing and decreasing the engine RPM, as well as for the horn. Enable buttons are on the transmitter and are required to be pressed in order to operate the crane, as a safety feature along with the Emergency Stop switch. The belly pack transmitter has the ability to run over an included tether cable in the event of a dead battery, and all functions can be manually controlled on the receiver/control box, or even using the manual levers.

Kar-Tech’s radios are proven safe and secure. The CAN actuators that control the valves are fast and precise to 0.01” with 90 pounds of force. They are environmentally hardened for all weather. An internal clutch allows the local operation of the valve handles without any effort when not in active wireless operation. This control is tough – all electronics are silicone dip-coated or encapsulated, every switch, joystick, and enclosure is sealed, and the transmitter is molded out of a high-impact rated plastic ready to take a beating on a job site. If you need additional functionality, custom configurations are available by request.


Each Bellypack RANGER System includes the following components:


PACKER Series Radio Transmitter

The PACKER transmitter is molded out of a high-impact plastic that’s durable from -40 to +185F (as are all components, including the electronics!). It contains switches for winch speed, and boom speed, and two for basket leveling (or use them for an auxiliary function).

It has either four or six fully proportional paddles for smooth control of your winch, boom elevation, boom rotation, and boom extension. The six-paddle version adds paddles for upper and lower boom elevation and extension, normally for knuckle-boom cranes. There are the enable horn, RPM pushbuttons, an E-Stop switch, and a three-position key switch for power and engine start – just like your car.

It runs off of internal rechargeable batteries that provide approximately 20 hours of operating life between charges. A high-quality padded shoulder strap is included.


Radio Receiver

This radio receiver module directly drives the actuators, crane switches, and all engine functions with two simple plug-and-play front-panel mounted sealed connectors. It provides all outputs based on transmitter commands. The ARM-powered receiver is housed in a sealed polycarbonate enclosure with industry-standard sealed Deutsch connectors. All I/O are protected against reverse battery connections, transient voltage spikes, short circuits, and overloads.

The system has an onboard backlit 2×16 character display for easy setup and configuration, manual backup, diagnostics, calibration, and histogram, driven by four sealed pushbutton switches. In addition to driving the actuators, it has multiple outputs for various throttle control types, and outputs for engine start, engine stop, horn, and basket tilt (or auxiliary). RS-232 is on-board for configuration as well.


12/24V Linear Actuators

These CAN-enabled actuators provide 90 pounds of force with a 3” maximum stroke and built-in processor for precise control of hydraulic valves. They have an internal clutch to enable freewheeling back to the center position when the joystick is released or power is lost as a safety feature, and are fully weather-sealed.


Bellypack RANGER Mounting Hardware Kit

Mounting Hardware Kit

This kit is comprised of adjustable linkage rods and clevises for connecting the actuators to the valve handles. The steel bracket is supplied by the installer.


Pre-Made Wiring Harness

This pre-made harness is designed to snap into each system component for an effortless installation with two sealed toggle switches for left and right pedestal remote power. All wires and connectors are labeled for easy identification. All sealed connectors are used, and cables are loomed together where required for a clean, plug and play installation. Crane connections such as RPM, horn, etc. are terminated in flying leads.


Check out how easily we retrofit this TEREX BT-3870-S Crane
with our CAN RANGER 4: Bellypack Ranger System


Want more information…?

Email us at [email protected]  for full installation and operation manuals.

by Haleigh Rozier | May 22, 2018

Eagle Signal manufactures electronic timer, electromechanical timer, and other devices. Within the electromechanical family is the HQ4 series of percentage timers. Percentage timers are a type of repeat cycle device that is compact and long-lasting. The HQ4 series is a unique timer that can function as an on delay, off delay, interval timer or repeat cycle device. Eagle Signal offers this accurate, economical, enclosed timer for a wide range of applications. Specifically, those where repetitive ON times of a fixed cycle requires adjustability. This series is a panel mounted unit with an exposed dial. The load relays’ seal protects against the environment. The HQ4 proves to be durable in industries such as chemical, feeding, irrigation controls, electric heaters, and motor controls. Recently, Eagle Signal developed an improved version of the HQ4 Series called the Cycl-Time® or CT4 Series.

CT4 series cycl-time percent timer/

The CT4 offers improved features including resolution, potentiometer, ease of setting, torque, safety, sealings, and wiring. Also, the Cycl-Time®’s resolution is more defined. For example, the colors of the faceplate offer more contrast for reading the time settings. With 100 ticks around the dial rather than 50, the CT4’s percentage options are more precise than the HQ4. The torque of the Cycl-Time® dial is more resistant to change than before. Once the timer is set, it will not rotate any further without intentional force from the user. These features combine to make the timer more accurate and easier to set. Safety is always the greatest concern when designing any product. The Cycl-Time® has a plastic guard over the terminal block to protect the user’s fingers from exposure to contractors. This percentage timer is ideal for applications environmental factors would usually cause concern. These features provide a longer lasting product and additional safety. The wiring and electrical connections of the HQ4 was also updated for the CT4. It now has four electrical connections, rather than seven, all in a straight line on the back of the body of the timer. As mentioned before, this timer is made to panel mounted. Eagle Signal continues to design the most accurate, economical, and reliable products in the industry. The HQ4 and Cycl-Time® Series are both exceptional devices fit for their specific applications. Cycl-Time® proves to be a respectable replacement option to the HQ4 Series.

CT4 Series CYCL-TIME Percent Timer

The robust cable transducers GCA5 are ideally suited for outdoor applications and cramped installation space.

The robust cable transducers GCA5 are ideally suited for outdoor applications and cramped installation space.

Sensor expert Baumer is further expanding their portfolio of cable transducers being the easiest, most reliable and cost-efficient way to measure linear motion within a path from 0.5 to 50 m. New series GCA5 is practice-proven when the going gets tough, for example at mobile machinery, and is ideally suited for use in cramped installation conditions.
The compact cable transducers of the GCA5 series do not compromise on maximum robustness in demanding applications. The housing of impact-resistant plastics, the corrosion-proof stainless steel cable with abrasion-resistant nylon sheath and the non-contact wear-free magnetic sensing make them the optimal choice for reliable and low-maintenance deployment in harsh environments. Thanks to the innovative design with three-chamber-principle, both electronics and stainless steel spring are hermetically encapsulated against the cable drum.  The integrated flexible dirt skimmer at the cable inlet is an additional protection against humidity and ingress of any other harmful environmental substance for maximum application reliability.
The cable transducers of the GCA5 series feature a maximum measuring range of 4700 mm and are available either with integrated CANopen interface or analog output 0.5…4.5 VDC. The CANopen variant provides additionally redundant position sensing and hence simplifies function monitoring at control level. Housing protection IP 67 (cable inlet IP 54), shock resistant up to 50 g, vibration proof up to 10 g and the extended temperature range from -40 to +85 °C make the cable transducers particularly robust and resistant against temperature fluctuations and all kinds of soiling.
The cable transducers of the GCA5 series excel by their narrow design and shallow installation depth of a mere 65 mm which allows easy installation even in cramped space – as prevailing in mobile machinery and utility or transport vehicles. Cable transducers series have been standing the test of time in outrigger positioning at mobile cranes and telehandlers as well as height positioning at floor conveyor trucks and stacker cranes. Whether as OEM equipment or for retrofit – the robust and compact cable transducers are ideal for precise measurement of linear motion in demanding applications.

View the entire line of Cable Transducers here:

https://andersoncontrol.com/shop/sensors/cable-transducer/

 

groupshot-w-trydynaparThanks to advancements in medical imaging technology in recent decades, doctors are now able to capture in seconds what used to take hours for diagnosis.
MRI is a noninvasive diagnostic technique that uses nuclear magnetic resonance to produce cross-sectional images of organs and other internal body structures. Dynapar offers a range of industry duty encoders designed to comply with FDA manufacturing guidelines for MRIs and X-Ray imaging. In x-Ray machines our encoders move water in and out of the machine, while in CT Scan and MRI machines they move patients in and out and measure the rotating speed.
Spacer

Recommended Solutions

H20 Hubshaft Encoder Try Dynapar

H20 Hubshaft

The H20, economical in size is the solution for your medical imaging application. It provides a wide range of resolutions along with a hubshaft with spring tether for easy installation.
 

 
 

AI25devicenet-Large

AI25 Absolute Encoder

Precise positioning and onboard diagnostics make the AI25 absolute encoder an ideal fit for your medical imaging application. Single turn and multi turn capabilities allow for the critical feedback required in medical imaging devices.